Wow 0 Minie - Winnie New Roof

This is a complete roof (cabin top) installation.  This should give you some ideas for your RV or boat.  Anyway, I thought it was pretty cool so I wanted to try and insert the video.

"The video used to be here but I was told to remove it for copyright reasons"

Plumbing with PEX

This is not an original thing but it acts as a library for myself and for others.  I had this installed in my Youngsun 35 and wished I had put  it in my Irwin 43.  This vLog is a good concise tutorial on using fittings with PEX.  I hope you enjoy it:

https://www.youtube.com/watch?v=WiqqhtFsMvU

Allstar Amatuer Radio System

This is one of many systems to implement an Allstar node.  This one uses an Alinco radio and it is a reliable system as long as you use low power mode and a fan on the power amplifier portion.  I have one operational and have used it for years.

The interface board is a RIM and along with a RaspberryPi and Alinco Radio you can have a system up and going in an hour or two.  Follow THIS LINK to get the general idea.

To get an idea of what Allstar is and how to build one go to Hamvoip website.  However, you will need to have an Amateur Radio license to legally operate this system and to get  a node number.  If you would wish to make a private node for only your self that is possible using a commercial radio licensed frequency or GMRS but check the rules for legal use of these frequencies.

AIS getting overloaded!

Automatic Identification Systems (AIS) are causing problems for mariners transiting waters where there are high concentrations of fishing vessels, particularly in the East China Sea. It seems the real problem is fishing nets where AIS has been installed to fool ships into steering clear of them (hundreds and hundreds of them).  Just be aware if you are a sailboat as it sounds like a place to avoid when possible.
Anyone who googles AIS Security will find out a lot about other spoofs/fake/distress fake broadcasts; re,  https://blog.trendmicro.com/trendlabs-security-intelligence/vulnerabilities-discovered-in-global-vessel-tracking-systems/

Inexpensive AIS Receiver

Large ships and passenger boats are required to broadcast an identification signal containing position, course, speed, destination, and vessel dimension information to help prevent sea collisions. This system is known as the “Automatic Identification System” or AIS for short. There are dedicated AIS receivers intended to be used on boats, or by hobbyists, but they can be expensive. A radio scanner, or the cheap RTL-SDR software defined radio (or a more advanced SDR such an Airspy) can be used to receive these signals, and with the help of decoding software, ship positions can be plotted on a map

https://www.rtl-sdr.com/buy-rtl-sdr-dvb-t-dongles

https://www.rtl-sdr.com/rtl-sdr-tutorial-cheap-ais-ship-tracking/

Watermaker 100 lph block diagram

The credits are on the picture so I do not need to do many disclaimers; however, I did pick this up from somewhere in my sojourn as a sailor. I do know Cruiser Forum had a recent watermaker article on the subject so I will put that link here too (I do not know if you need a subscription to see it though).

Also, here is another way, Salt Water Pro , to go with so many ways to configure.  I think individual components is a good way to construct yours since you can put the bits and pieces anywhere.  The quiet motor option sounds good (pardon the pun) but I have never heard one running so I do not really know.

I am a patreon of Emerald Steel watermaker and they maid their own watermaker.  It is presented on Youtube and has names, places and how-to's for building watermakers.  Well worth the listen but it has the usuak Youtube commercials at the front.

Marine & Other Solder Joints

 

Almost everyone using leaded solder on a boat or shop bench will be using the much cheaper, older style, 60/40 solder with an unknown flux. The solder can be oxidized or corroded on the outside of the reel as well.  I know this has happened to me and continues to happen as I do not really solder a lot any more.  So only buy a limited quantity from Digi-Key, Mouser or other reliable supplier.  Quite often I use Amazon but lately Digi-Key is getting most of my business.  There is no minimum order with then anymore.

63/37 solder is better. It has a higher tin content. The main advantage is this is a eutectic solder. Basically this means the solder only has one melting temperature. 60/40 solder has a temperature range. Once it is hot enough to melt, it has to cool down to a lower temperature before it solidifies. An joint movement during this solidification process will result in a poor joint. Joint movement is a joint killer and this happens even with professional had solderers. You can imagine what some of mine look like.  A cold solder joint will be dull colored, whereas, a good joint will be shiny.


Here is an example of  what you should look for:

Kester 24-6337-0027 Solder Roll, Core Size 66, 63/37 Alloy, 0.031" Diameter

This is only an example so be aware that many different lengths and diameters are available.  I tend to use the smaller diameter solder and if it has to be thicker for major joints I double or triple, etc. the solder and twist it to make a bigger diameter. Since this is not ideal, if you have a lot of bigger joint work to do buy the larger diameter. Kester solder has been around for a long, long time and I used to use it back in my early electronics days.The link above will take you to their site and you can download literature and specs on their products.

Deep Breathing

For being free and incomparably easy to practice, deep breathing is a pretty miraculous healing exercise: It can reduce anxiety, bring you into the present moment through mindfulness, and even help you remember how to respond to your specific stressors.Follow the link below for much more detail.


https://www.thecut.com/2018/12/what-deep-breathing-does-to-your-body.html?utm_source=pocket&utm_medium=email&utm_campaign=pockethits

Aircraft Noise Complaint Device

This is a very innovative device and just demonstrates how new technologies allow innovative thinkers develop useful devices.

Imagine you live close to a major airport, and since NextGen has changed many air routes in the last few years, a lot more noisy airplanes fly right over your house. Now it’s easy for those citizens to file a noise complaint — instead of facing hours of paperwork, they can just push a button on a thumb-size device like those used by Amazon shoppers to order household goods. Here is a link to the Air Noise website.